It uses some people’s favorite anchor to knock on the door, you can hear it, but I prefer stud detectors, the floor joists operate in one way or another, so I recommend going this way, no, the opposite direction, But I can see the arrow, so it shows that my mark is not on the stud, I need to use an anchor, the light has an anchor, but I prefer to use these small screws, let me tell you, this is a screw and an anchor, I like to use everything I have now. 

Tap the hammer lightly into the ceiling and screw it in with a screwdriver. Then you can use its built-in hook or this more beautiful little device, put it on the ceiling, and then tighten the screws like this so that you can hang the cable here. I just put it on the ceiling. There is nothing like putting it on the ceiling. It is easier to drag the cable behind the curtain. This is the planning checklist that actually comes with the manual, telling you how far the light should hang on certain plants and how long the light should run. No matter what stage of the growth stage, plants are going through such a perfect process.

The plant growth lamp is a special kind of lamp. It needs sunlight to follow the law of plant growth. The plant growth lamp is a lamp that uses the principle of sunlight to replace the sunlight to provide the environment for plant growth and development. Generally, indoor plants and flowers will change in time and grow worse and worse. The essence is to produce light. The LED light that is suitable for the required spectrum of plants can even promote it and apply this high-efficiency light source system to greenhouses, greenhouses, etc. In terms of agricultural production such as facilities, it can solve the disadvantages of insufficient sunlight that causes the taste of greenhouse vegetables such as tomatoes and cucumbers to decrease. At the same time, it can also make the winter solanum vegetables listed in the greenhouse before and after the Spring Festival, so as to achieve the purpose of off-season cultivation.

1. As a supplementary light, the light can be enhanced at any time of the day and the effective lighting time can be prolonged.

2. Whether it is at dusk or at night, it can effectively extend and scientifically control the light required by plants.

3. In a greenhouse or plant laboratory, it can completely replace natural light and promote plant growth.

4. Thoroughly solve the situation that the seedlings need to be eaten according to the day, and arrange the time according to the delivery date of the seedlings.

It is divided into many requirements, similar to the light intensity, photoperiod, and light quality. The photoperiod refers to the light and dark photoperiods of the day. The light of different wavelengths has different effects on plant growth. Therefore, in the nursery We often use light blue plastic film to cover it, which is transparent. Ultraviolet light can inhibit the growth of plants, and with the colorless film index, the light blue film can make the embryo grow more robust.

The laser plant growth system is a plant growth system developed to promote plant photosynthesis by using laser synthetic plant photosynthesis spectroscopy technology!

The laser plant growth system has the function of providing effective light to green plants. The time can be set arbitrarily, which can prolong the effective time of photosynthesis of plants every day, especially on cloudy and rainy days. Plants can grow normally on hazy days, as well as seedling factories and plant factories.

As you can see in the example image here, it seems that Lux is at least slowly disappearing, at least for indoor growers, photosynthetically active radiation is a plant-specific method that only measures what the plant can actually use for photosynthesis Light, and the lumens usually expressed on a certain surface area of ​​Lux is just a more general measure of the overall light intensity without considering the factors related to photosynthesis. This makes the photometric measurement of indoor gardens more accurate, because lumens and lux are still widely used. The reason for use is basically well applied. This is because the cost of a luxury meter is only one tenth of its cost, so many growers only use Lux, especially when you use an outdoor grower, the sun Can provide very good performance, so you really don't have to worry, but anyway, if you want to view them, you can link to a parameter table and a link to an illuminance meter in the video description.

The ppfdor photosynthetic photon flux density is just a way to express the same level. It is actually a unit measured in micromoles per square meter per second, ppfdis. It is just the number of readings displayed in meters at the same level. Therefore, this is what you want during the growth Although God knows that you may go far and high, it just means that the growth rate slows down, and so on. For your seedlings, clone the mother plant, your plant nutrition will reach 1 250 to 400 ppfd ceplants, you want 400 to 600 ppfd, flowering plants, you will need 16 to 900 ppfd, but for your leisure growers, don’t worry, if you are below 600 ppfd, you will still get growth. You will still get that the rate of production decline will not be so fast or so fast. Some of you indoor growers always want to know, if I can be taller like the above athousand ppfd, can you be taller? For example, we conducted an interesting study at the University of Mississippi in 2008, which proved that the dominant plant of asativa originated in Mexico. As long as the air temperature is kept below 30 degrees Celsius, the strain that can withstand its light intensity will actually be 1500 ppfd. The speed increases sharply, but the higher the temperature rises by 1000 ppdd, the less profit is gained for each additional point, and the more difficult it is to increase access, the more you own, you either have more growth lights, or you have Better grow lights, or make existing grow lights closer to the plants, which of course will lead to the first method of taking more kinds of plant growth light may also cause you to heat up, and remember that as an indoor grower, you The role of is usually to grow the most efficient plants, not the fastest way to grow plants, and in the fastest way of planting, you spend the most money is the best.

The rule of thumb is that if your price exceeds 950 to 1,000 ppfd, your economic efficiency is not high. Even if you use high-efficiency LED lights, I don’t know why the University of Mississippi has done so much research on cannabis. They are even those People who have been engaged in pattern monitoring projects for decades, maybe I have to interview someone from there, because I really want to know why in such a state with such a retrospective history of cannabis, you have a university that has done all of it so well. The research, this is the powerful force of my quick start guide, I hope you find it useful.

Mycin is the third point to the south. I have discussed it. , But in the northern hemisphere, south-facing windows will get direct light. Use your phone to install such a compass app, it will know which direction natural light shines, which will help you understand what kind of light you will have in that situation Intensity space, so we completed three tasks. First, we don't call them "Indoplants", but treat them as low-light plants. Secondly, indoor lighting varies from place to place. ThirdPoint suddenly changed the northern hemisphere. The windows of the southern hemisphere suddenly tilted to the south, where the Indians got direct sunlight. There are four very important points: artificial light bulbs can help you, if you have a light bulb or downlight, it will help you. Plants try to get plants close to the light source. What you can do now is own a desk lamp or desk lamp. Then place them on another plant that will be used. This will be another method, which is to place plants on top of refrigerators or cabinets or similar items, bringing them closer to fluorescent or ceiling lamp bulbs. Remember that any kind of artificial light can help you grow plants. Chat in the dark corner, if you add a small light bulb, if we hope to develop a kind of friendship talent, it will help you. The equipment I want to provide you is that if you see plants, you will think I can keep them, so let us review the origin history of these plants that you remember in school or a small class. We have already read about rain forests. Rain forest, they have different levels. Plants are now growing plants. Most indoor plants grow naturally. They come from these tropical rain forests. In almost all tropical rainforests, these are benthic animals. In the rainforest, there are big trees that form a roof, and they form such a thick roof. Only filtered light can pass through such a huge space. Therefore, plants living under these filtered light are very suitable for low-light environments, such as Our palm trees. This is why these plants are brought home, so all these plants (such as money-saving plants, zizi or fern enema) can perform well under diffused light. What is diffused light that does not shine directly on it? ?

Please note that when sunlight shines directly on the leaves, these plants will burn,Therefore, even if they are cooked in a cool place, they work well, and you can also know if I can keep the plants indoors, or you will find yourself familiar with money plants and find seaweed roots. Any plant with these aerial roots is most likely to forage from the bottom of the jungle. These plants must climb to the trees to truly grow and survive in these places. Everything with signs of aerial rooting will be well done in your house, this is a little trick you can take away, so you will find singhania m – you will find wandering Jews, various money plants, all monstera , You will see here, all the nodes and theaters visited are rooted in it. You can bring them into your home very safely and have a good time with them, but one more important thing is that we brought these plants into the plants, but as we discussed in the first point, These plants did not proceed by themselves, they will be weaker plants, they will prefer bright light, but when you provide them with low light, they can survive, they will not try, but they can survive, so we have to What we do is make sure our plants are happier.

This is called rotation, and now you can rotate in both directions. One is that if there are fewer plants, an easy way to rotate is to take them to a balcony or a sunny place. This is the same as the spa treatments we enjoy in winter. You love the world and use the same way to sit in the sun, imagine you are providing a better environment for today's toy plants. Now, I say that there are more plants, and there are better ways to exchange, which can be exchanged in one week outdoors and one week indoors, so let’s imagine that I have two plants and only in one room a week Just keep one plant, when the other is outdoors, then I will swap next week, and then it doesn’t matter which one you follow, but as long as you give the plants some sunshine outdoors regularly, they will like it, so let’s modify it, Let's modify it quickly, don't call it here. Indoor plants call them low-light plants. This is the first step in order to better understand your plants. The second thing is that indoor light is relative. It changes with location. When you decide where to place plants, Remember the third thing about the purpose. The compass will be located on the south side of the southern slope of Nanchuang. Get direct sunlight at the fourth point in the northern hemisphere. The very important artificial light also helps, so any cubes (such as any bulb LED bulbs) will help, then the fifth point will help us remember that these plants come from the rainforest, any tall root plants are you can be in the indoor environment, then finally One point, the last point is to rotate, once a week, and then try to do it yourself on the ntsa days of the sun, they can provide them with the best environment, when they want them, this will actually help your plants better Grow.

GLMX is designed to work in a certain way and use sunlight, so you want to give them white, yellow or sunlight colors to make them have a full spectrum, they will flourish, not just purple and red-purple will cause eyes Damage, you need a second set of white light, or you need sunglasses to work in blue and red light, they are very bright and are also at the end of the line of sight, so you may not notice how bright they are because they are always facing blue The color ultraviolet light, then turns red, towards the infrared, so they are a bit far from what we see, so you may not even notice the damage these plants do to you. You worked under these plants and you left me. When you leave the ultraviolet rays, justice will hurt your eyes. It's very dark, I'm not sure you will see small dark spots, I will put another small picture to see if you understand UV spots, but these spots are dark, but also very strong. If you stare for too long, ultraviolet rays can easily blow up your eyes. Of course, you know that certain things are reflected, so ultraviolet rays will directly enter your eyes when you work. Therefore, when you actually work on the plants next to it, you need a second light source.

Because of the color, it cannot tell you the problem with the plant, because it prevents you from knowing whether the plant is healthy or unhealthy. It turns yellow, etc., because it can’t really distinguish the strange light on it, so if you use the blue and red spectrum, you must always switch to regular light to work under plants, so the blue in the next cycle Same as the red LED indicator. The white LED light is a blue LED light, coated with a yellow phosphor. The blue light reacts with the yellow phosphor coating to produce white light. That is all the problem. He applies the same amount of energy to the blue and red LEDs and the white LED. There is a myth that all blues and reds are more effective than white, but this is not the case. The main energy is very little. The problem is to use blue and red instead of white, so make sure not to add ultraviolet light to plants, because it is difficult to detect how much ultraviolet light they can absorb with ultraviolet light-the ultraviolet light you give plants can easily kill seedlings and/or adult plants, Because I did it myself, I put the light too close to the plant, it withered, as if it melted, as if it turned yellow, as if completely dead, I planted some seedlings, I planted some, just Like nothing sprouted, because they are only used to scramble the soil because I am too close, so if you get these types of light, please make sure I even put the tape on the Iput tape and cover it with a little UV because the plants don’t It needs ultraviolet light to grow, and the plant is the right ultraviolet light to resist, because this is part of the ultraviolet light, it will only damage the plant, and then the plant must protect itself from harm, so what will happen is that the leaves of his plant will Thicken to resist radiation, and some plants produce oil.

Therefore, if you are a lavender grower and you have grown plants indoors and want to get the necessary oil from the lavender plant, you can give it some UV rays to increase the oil content on the leaves, thereby increasing the yield, but if you are not Lavender growers, I strongly recommend that you do not use ultraviolet light in your plants. Finally, I will conduct a test to see which plants grow better under blue and red LED lighting or white LED lighting. This is not a super scientific test. Using the white LED I own, I also own this purple LED, so I have set it up, and now I want to build another factory at the same time, we will test the results together, it will take about one or two months of video processing data And plant planting to observe the difference in growth.

Therefore, a good idea is to build a mirror around the window, especially when the window is inserted into the wall. Therefore, this is a good example. I like to show people these mirrors because sometimes they think it is a real window and tell them the direction of the window looking inward is opposite to what you see. Now I had to delete these recently because the contractor had to come in and actually finished the edge of the window, so there is no light difference between these mirrors, so there is no mirror. These mirrors are actually very important, so I think people can use you to hang the mirror in different ways so that you can hang the mirror facing the window to slide backward. These are very smart and small and are now easy to install in the home to increase light.

Solution 2: I don’t personally have many white walls, but when you consider buying new apartments and new apartments, they are always white walls. Most of my walls are green, blue and red, and all the different colors, because I like to save some white walls. In fact, white walls can reflect light back. The reflected light is not very good, but it is enough to allow plants to get more extra light. This is the same way you take the picture, and there is a white bounce card, in this example, it will bring a small amount of ambient light to the surrounding plants or plants.

The last idea is to bring more light to your space by adding light. Whether it is a plant light or an ordinary light, it will be very appreciated. I have some clever ways to do things that are helpful to the things under the shelf, so here I am. This is a light bar. It is an LED light bar. In fact, it doesn't even light up, so you only need to touch it and it will light up. It is very suitable for small plants now under the shelf. There is another shelf lighting under the shelf, so you don’t have to think of it as a fluorescent light, it’s a plastic barbecue light, it’s actually on sale, it’s a bit hot, I must be very hot, it actually heats the top of the counter, so I must Be very careful, in fact, this might be a good place to actually start sowing because it is warm enough to be planted here, but this fluorescent light does get a little hot. Therefore, you must pay special attention to plants that are actually growing and actually burning themselves. You can see my Peperomia fairway is here. The floret is actually better and is burned by fluorescent lights, so that's why you need to pay more attention to it, but the advantage of being able to put it on a shelf is that you don't actually have to stare at it.

Then, I will show you other ways to increase the brightness. In the past, bright lights were highlighted on the channel in front of my eyes, but this is a good choice, this is from Sol technical solutions, I like these lights, in fact, I will save 15% in the description below The code is well described in other indicators. These are great. There are three in my family. They are a bit like a pendant shape, so even if you get strong light from here, of course, here, you also start to enter the low to the medium-light range, so you will notice that many of my plants here are plants that can handle more weak Light, of course, you can also grow bulbs, so this may not be the most beautiful lamp, but I have a bulb here, a torture lamp for me, for Sansevieria or Dracaena Troy Fosse otta, for those who know it belongs to a new genus, Actually it is the Dracaena, I am a nanny or sitting with a friend who moved out, so this friend is a bit extravagant. There is a growth bulb. This is the VANQ growth light. They have these different varieties. I use other growth bulbs.

VANQ's lights enter such lights and then illuminate them on the ceiling, you can use it. It started with a white surface, so in fact, this is one of the ones I will link to in the description below. Other GE grows lights reflect the light from the ceiling and then reflect downward, and then the light in the shower room is really good. Therefore, I hope to give you some new ideas on how to bring more benefits to your home, trust me, your plants will thank you, so another strategy you use is to make your plants more illuminated.

Because I will discuss led grow light more, and the upcoming experiment is the third article in this series, the next one we will use the same lighting, plant nutrition, and flowering stage test two articles. I chose to use the cracking method in the same container where all plants are grown in China because I found in past experiments that using stones may cause errors or inconsistent results. I don't understand why I should consider viewing the link in the article. In order to make these articles easy to understand, please explain below. I will provide specific details in the article description, so if you want to know more, please forget to read more.

For some Greenhouse Grow Light ideal information, see the details below. Please comment. I will try to answer and add it to the description. In the future, let us look at the results at the end of the test. Obviously, although the white light of the lettuce is slightly elongated, it is not disappointing. I’m about to talk about the method of secondary elongation of the leaf just because the white LED is 3000k instead of 4,000K or higher, so I prefer red light with a color temperature equal to two lights, but this does not mean using 4 Or 5,000 K white LED will produce fewer plants. The first thing I saw was that the burning tip jacket plants showed slight tip burning, but these plants were burned throughout the test.

The blue light that is not red is just a bit more, but not enough to pay attention to the healthy growth of the roots of all plants. However, under red and blue light, the root quality of plants is slightly lower. The second thing I noticed is comparing red and blue lights with white lights. The plan is slightly different. I think this is the dark green of the chlorophyll in the leaves, but there may be a better scientific answer. So if you are different now, please leave a comment. Important information I weighed the measures to be taken for each plan. Under white light, the average weight of the plan is 118 grams, totaling 473 grams, and the average red and blue light produced by each plant is 86 grams, and the average is 347 grams, so now it is about producing white LED. For you, under red and blue lights, the factory quality is 37% higher than planned. I want to know if they have tasted different flavors.

They did it. I can't really say the normal taste, but it can be said that there are more red plants than the rest and even the skin. The face is pale, but still a bit bitter, so when I end this article, I will let you gain and lose in this regard. This article uses the toon spectrum. For example, red and blue light cannot conclude that toon's spectral light is good or bad for different plants. Different growth stages play an important role in dimming methods. So, if you seem to be otherwise, since the hobbyist's white light is a simple fail-safe option, in order to figure out that I didn't bring me the answer in the article, thank you very much for watching.

It takes several weeks for germination. Check your seeds first. They should be brown, hard and dry. If they look green and fresh, they are not yet ripe and will germinate seeds. The required equipment is incomplete. Cutting-edge technology, two boards, four boards, kitchen paper rolls. Some distillation works like this. Don’t forget to moisten the seeds first, but don’t soak the kitchen paper with distilled water, then place two of them on top of the sheets Place a plate, place four beds, and then separate the seeds about an inch, then place the remaining two sheets of paper on top, and press lightly.

They eventually twisted the second plate, placed it on top to form a dome, and then placed the seeds in a dark and humid place to help them germinate. Heat it up a bit to keep it in the temperature range of 70 to 90 degrees Fahrenheit, and then check to see if the paper is used up in the next few days, but don’t over soak it, you will know that when the seeds germinate, they will crack. This is the so-called taproot will begin to grow at this stage, resisting the temptation to touch.

Your seeds are very fragile and easy to multiply bacteria, so the seeds will become smaller than a two-inch flower pot. Use compost to almost fill the top. Make a small hole about a quarter of an inch in the center o f the compost with a pencil, and use tweezers to gently transfer the germinated seeds into a spray bottle to moisten the soil and keep the taproots facing down. But if the compost is too wet, the seeds May wither.

Now let’s talk about the second part, which is lighting. Of course, healthy germinating seeds must be moisturized by sunlight. My experiments have proved that 10W-50W LED Grow Light is most suitable for cultivating seeds to germinate. LED lighting can not only provide plants with the nutrients they need, Can also accelerate the efficiency of growth.

If you are worried about how to choose LED lights for germination, I highly recommend you to search for VANQ LED Grow Light, they specialize in LED research, and the quality of the lamps is guaranteed. If you like this article, please click below Join us in the comments section.

The cucumber I chose is a variety called pica lino. It can produce all female flowers without pollination, so it is very suitable for growing indoors or in a greenhouse on the 25th day. Due to powdery mildew, it has removed some leaves. Even with powdery mildew, the plant showed tremendous growth. I was surprised how many flowers bloomed in such a short time on the 30th day, there were no signs of powdery mildew, and many new leaves were replaced. Some cucumbers began to grow.

The armor-piercing T8 is worthy of the name, because it can penetrate many canopies and induce many flowers and flower buds to be actually loaded. Plant flowers and new buds within 25 days after transplantation. After the cucumbers are removed, they grow at an alarming rate. Picking on the 35th day took 7 to 10 days. We harvested the first batch of grapes and one of my students. In the end, we picked 8 cucumber dat from the vine, which was our last harvest, because the cucumber plant has completely exhausted its life and produced 191 cucumbers. My students and I like to eat fresh things. We also sell it to our employees. With the help of many other cucumber schools, we eventually raised $125 to maintain and support our indoor garden.

To my surprise, VANQ Hydroponic LED Grow Light T8 can produce 191 cucumbers in an area slightly larger than 4 square feet. In this region, the penetration cost of water and electricity growth T8 is $649 for three years. The 12-year warranty from the day the lights are turned on is only $54 per year. I can easily repay my money within 24 weeks. My class has 3 cucumbers provided by school staff, the price is 5.00 US dollars, they are organic seeds, we do not use any herbicides, pesticides or fungicides, our cucumbers increase the value and demand of our products, to us The demand is so great that I must start reducing the number of people who pay in advance to ensure that if we sell all 191 cucumbers, they will have the next right to pick them. They could have sold 63 bags of luggage for $5 and could raise $115 in 3 days and 80 days.

You can pay for these two cucumbers. After that, in the next 11 and a half years, for every cucumber planted, the school community association may be a non-profit organization, or even an individual, and a healthy and good organization. The high yield index of a plant is the number of days the roots have grown since the 1980s. The root system of cucumber is the healthiest root system. I see them very white. I am a pioneer in Sookie's contribution to VANQ growers because it generates almost no heat. To help me lower my body temperature, a lot of oxygen enters the VANQ spectrum. Insufficient light can also have a huge impact on plant health and high yields. Looking forward to buying more lights from VANQ from the classroom